Honeywell 4600g Guía de usuario

™ 4600rp, 4600g/4600r, 4800iCommercial/Retail/Industrial Area ImagerUser’s Guide

ivChapter 5 - Data FormattingData Format Editor Introduction...5-1To Add a Data Format ...

7 - 6When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 barcodes printed with a check character, but will not tr

7 - 7Code 32 Pharmaceutical (PARAF)Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known

7 - 8Character pairs /M and /N decode as a minus sign and period respectively.Character pairs /P through /Y decode as 0 through 9.Code 39 Code PageCod

7 - 9When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 barcodes printed with a check digit, but will not

7 - 10Code 93< Default All Code 93 Settings >Code 93Code 93 Message LengthScan the barcodes below to change the message length. Refer to Messag

7 - 11Straight 2 of 5 Industrial<Default All Straight 2 of 5 Industrial Settings>Straight 2 of 5 IndustrialStraight 2 of 5 Industrial Message Le

7 - 12Straight 2 of 5 IATA (Two-Bar Start/Stop)<Default All Straight 2 of 5 IATA Settings>Straight 2 of 5 IATAStraight 2 of 5 IATA Message Lengt

7 - 13Matrix 2 of 5<Default All Matrix 2 of 5 Settings>Matrix 2 of 5Matrix 2 of 5 Message LengthScan the barcodes below to change the message le

7 - 14Code 11Check Digits RequiredThis option sets whether 1 or 2 check digits are required with Code 11 bar-codes. Default = Two Check Digits.Code 1

7 - 15Code 128<Default All Code 128 Settings>Code 128ISBT 128 ConcatenationIn 1994 the International Society of Blood Transfusion (ISBT) ratifie

vInterleaved 2 of 5 ... 7-8Code 93 ...

7 - 16Code 128 Message LengthScan the barcodes below to change the message length. Refer to Message Length Description (page 7-2) for additional info

7 - 17Telepen<Default All Telepen Settings>TelepenTelepen OutputUsing AIM Telepen Output, the imager reads symbols with start/stop pattern 1 and

7 - 18UPC-A<Default All UPC-A Settings>UPC-AUPC-A Check DigitThis selection allows you to specify whether the check digit should be transmit-ted

7 - 19UPC-A AddendaThis selection adds 2 or 5 digits to the end of all scanned UPC-A data.Default = Off for both 2 Digit and 5 Digit Addenda.UPC-A Add

7 - 20UPC-A/EAN-13 with Extended Coupon CodeUse the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the

7 - 21UPC-E0 ExpandUPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off.UPC-E0 Addenda RequiredWhen Required is scanned,

7 - 22UPC-E0 Number SystemThe numeric system digit of a UPC symbol is normally transmitted at the begin-ning of the scanned data, but the unit can be

7 - 23EAN/JAN-13<Default All EAN/JAN Settings>EAN/JAN-13EAN/JAN-13 Check DigitThis selection allows you to specify whether the check digit shoul

7 - 24EAN/JAN-13 AddendaThis selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data.Default = Off for both 2 Digit and 5 Digit Addenda

7 - 25ISBN TranslateWhen On is scanned, EAN-13 Bookland symbols are translated into their equiv-alent ISBN number format. Default = Off.EAN/JAN-8<D

viPostal Codes ...7-38Intelligent Mail Barcode ...7-38ID

7 - 26EAN/JAN-8 AddendaThis selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.Default = Off for both 2 Digit and 5 Digit Addenda.E

7 - 27MSI<Default All MSI Settings>MSIMSI Check CharacterDifferent types of check characters are used with MSI barcodes. You can program the im

7 - 28MSI Message LengthScan the barcodes below to change the message length. Refer to Message Length Description (page 7-2) for additional informati

7 - 29GS1 DataBar Omnidirectional< Default All GS1 DataBar Omnidirectional Settings >GS1 DataBar OmnidirectionalGS1 DataBar Limited< Default

7 - 30GS1 DataBar ExpandedGS1 DataBar Expanded Message LengthScan the barcodes below to change the message length. Refer to Message Length Descriptio

7 - 31PosiCode<Default All PosiCode Settings>PosiCode A and BYou have to have PosiCode A and B on to read any of the PosiCode symbolo-gies.PosiC

7 - 32Trioptic CodeNote: If you are going to scan Code 32 Pharmaceutical codes (page 7-7), Trioptic Code must be off.Trioptic Code is used for labelin

7 - 33Code 16K<Default All Code 16K Settings>Code 16KCode 16K Message LengthScan the barcodes below to change the message length. Refer to Mess

7 - 34Code 49<Default All Code 49 Settings>Code 49Code 49 Message LengthScan the barcodes below to change the message length. Refer to Message

7 - 35PDF417< Default All PDF417 Settings >PDF417PDF417 Message LengthScan the barcodes below to change the message length. Refer to Message Le

viiOCR Templates ... 9-3Creating an OCR Template... 9-3Stringin

7 - 36MicroPDF417< Default All MicroPDF417 Settings >MicroPDF417MicroPDF417 Message LengthScan the barcodes below to change the message length.

7 - 37UPC/EAN VersionScan the UPC/EAN Version On barcode to decode GS1 Composite symbols that have a UPC or EAN linear component. (This does not affe

7 - 38Default = GS1 Emulation Off.TCIF Linked Code 39 (TLC39)This code is a composite code since it has a Code 39 linear component and a MicroPDF417 s

7 - 39ID-tag (UPU 4-State)Note: You may enable the ID-tag (UPU 4-State) if you have firmware with a base number of 31205480. Refer to the Show Softw

7 - 40Planet CodePlanet Code Check DigitThis selection allows you to specify whether the check digit should be transmit-ted at the end of the scanned

7 - 41British PostCanadian PostKix (Netherlands) PostNote: Kix code can misread when scanned sideways or upside down. Use Working Orientation, page 3

7 - 42Australian Post InterpretationThis option controls what interpretation is applied to customer fields in Austra-lian 4-State symbols. Bar Output

7 - 43Japanese PostChina Post<Default All China Post Settings>China PostChina Post Message LengthScan the barcodes below to change the message l

7 - 44Korea Post<Default All Korea Post Settings>Korea PostKorea Post Message LengthScan the barcodes below to change the message length. Refer

7 - 45QR Code< Default All QR Code Settings >QR CodeThis selection applies to both QR Code and Micro QR Code. Note: The default applies to firm

viiiChapter 12 - Serial Programming CommandsConventions...12-1Menu Command Syntax ...

7 - 46Data Matrix< Default All Data Matrix Settings >Data MatrixData Matrix Message LengthScan the barcodes below to change the message length.

7 - 47MaxiCode< Default All MaxiCode Settings >MaxiCodeMaxiCode Message LengthScan the barcodes below to change the message length. Refer to M

7 - 48Aztec Code< Default All Aztec Code Settings >Aztec CodeAztec Code Message LengthScan the barcodes below to change the message length. Ref

7 - 49Chinese Sensible (Han Xin) Code< Default All Han Xin Settings >Han Xin CodeHan Xin Code Message LengthScan the barcodes below to change th

7 - 50

8 - 18Imaging CommandsThe image scanner is like a digital camera in the way it captures, manipulates, and transfers images. The following commands al

8 - 2Step 1 - Take a Picture Using IMGSNPImage Snap - IMGSNPAn image is taken whenever the hardware button is pressed, or when the Image Snap (IMGSNP)

8 - 3L - LED StateDetermines if the LEDs should be on or off, and when. Ambient illumination (0L) is preferred for taking pictures of color documents

8 - 4G - GainGain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As yo

8 - 5% - Target Set Point PercentageSets the target point for the light and dark values in the captured image. A setting of 75% means 75% of the pixe

ixAppendix A - Reference ChartsSymbology Chart...A-1ASCII Conversion Chart (Code Page 1252) ...

8 - 6IMGSHP ModifiersA - Infinity FilterEnhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not

8 - 7E - Edge SharpenAn edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the

8 - 8H - Histogram StretchIncreases the contrast of the transmitted image. Not available with some image formats. 0H No stretch (default)1H Histogr

8 - 9IF- Noise ReductionUsed to reduce the salt and pepper noise in an image.0if No salt and pepper noise reduction (default)1if Salt and pepper noise

8 - 10J - JPEG Image QualitySets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger file

8 - 11nB The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 480. (Default = all rows)Alternately, s

8 - 12S - Pixel ShipPixel Ship sizes an image in proportion to its original size. It decimates the image by shipping only certain, regularly spaced p

8 - 13nU Apply document image filter using grayscale threshold n. Use lower numbers when the image contrast is lower. 1U will have a similar effect

8 - 14W - Histogram ShipA histogram gives a quick picture of the tonal range of an image, or key type. A low-key image has detail concentrated in the

8 - 15To see this example, align the aimer with the signature area (not with the bar-code), then press the trigger. Send the following IMGBOX command

x

8 - 16B - Output Image Height This option is used to size the image vertically. If using this option, set the resolution (R) to zero.D - Pixel Dept

8 - 17K - Gamma CorrectionGamma measures the brightness of midtone values produced by the image. You can brighten or darken an image using gamma corr

8 - 18R - Resolution of Signature Capture AreaThe resolution is the number of pixels that the imager outputs per each minimum bar width. The higher t

8 - 19X - Horizontal Barcode OffsetThe horizontal barcode offset allows you to offset the horizontal center of the signature capture area. Positive v

8 - 20

9 - 19OCR ProgrammingUse this section to program the Imager for optical character recognition (OCR). The 2D imager reads 6 to 60 point OCR typeface.N

9 - 2OCR-B On allows you to scan characters in the OCR-B font. The default set-ting allows you to scan any eight digit combination. If you have crea

9 - 3SEMI FontSEMI Font On allows you to scan the SEMI font used in the semiconductor industry.All OCR Off turns off all OCR capability in the imager,

9 - 4Template CharactersNote: OCR templates default to eight digits, no check character. To Add an OCR Template1. Turn on the OCR font you want to re

9 - 5Character Match SequencesThis method is used if you need a template that shows a specific character in a specific position. Put the character in

1 - 11Getting StartedAbout This ManualThis User’s Guide provides installation and programming instructions for the 4000 Series imagers. Product speci

9 - 6To create this template, you would enable the OCR-A font. Scan the Enter OCR Template symbol (page 9-13). Scan the d from the OCR Programming C

9 - 7Reading Multi-Row OCRThe imager is capable of decoding multi-row OCR text. Note: Reading rows longer than sixteen characters is not recommended

9 - 8Example: You need to read any combination of seven digits, with a modulo 10 check character in the eighth position. The template would be:dddddd

9 - 90123456789XAlso enter the OCR template:dddddddcEnable the OCR-A font, then scan the following string:6512351XThe imager performs the following ch

9 - 103-1-3-1 Weighted Modulo 10 Check CharacterStarting with the check character and working backward through the message, the imager applies a multi

9 - 11Then scan the string below:0128454The reader performs the check character computation below:(0 x 1 + 1 x 2 + 2 x 1 + 8 x 2 + 4 x 1 + 5 x 2 + 4 x

9 - 124. Scan the symbol below to set up three templates to handle the ISBN number, the three digit price field, and the four digit price field.5. Fin

9 - 13OCR Template CodesNote: Reading more than three rows of OCR is not recommended. Contact the factory if you have an application that requires re

9 - 14

10 - 110Interface KeysKeyboard Function RelationshipsThe following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships appl

1 - 2Imager ModelsThe chart below lists the interfaces that can be used with your imager. Refer to Chapter 6 for programming information regarding se

10 - 2The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of th

10 - 3Supported Interface KeysASCII HEXIBM AT/XT and PS/2 Compatibles, WYSE PC/ATSupported KeysIBM XTs and CompatiblesSupported KeysIBM, DDC, Memorex

10 - 4Supported Interface Keys ASCIIHEXIBM, Memorex Telex (102)*Supported KeysMemorex Telex (88)**Supported KeysNUL 00 Reserved ReservedSOH 01 Enter E

10 - 5Supported Interface KeysASCII HEXEsprit 200, 400ANSISupported KeysEsprit 200, 400ASCIISupported KeysEsprit 200, 400PCSupported KeysNUL 00 Reserv

10 - 6Supported Interface KeysASCII HEXApple Mac/iMac Supported KeysNUL 00 ReservedSOH 01 Enter/Numpad EnterSTX 02 CAPSETX 03 ALT makeEOT 04 ALT break

11 - 111UtilitiesTo Add a Test Code I.D. Prefix to All SymbologiesThis selection allows you to turn on transmission of a Code I.D. before the decoded

11 - 2Show Scan Driver RevisionScan the barcode below to output the scan driver revision. The scan driver con-trols image capture.You may use the Sho

11 - 3Test MenuWhen you scan the Test Menu On code, then scan a programming code in this manual, the imager displays the content of a programming code

11 - 4You can exit Full Report mode by either typing the menu command, 2D_PQA0, if you are using Quick*View, or by scanning the following barcode:Note

11 - 5Scan DataScan Data allows you to scan barcodes and display the barcode data in a win-dow. Scan Data lets you send serial commands to the imager

1 - 3Imager IdentificationCompliance Label locationItem Number, Serial Number and Revision Information location

11 - 6Quick*ViewQuick*View is a Microsoft Windows® program that displays decoded symbol messages and captures images (for instance, ID photographs) fr

12 - 112Serial Programming CommandsThe serial programming commands can be used in place of the programming barcodes. Both the serial commands and the

12 - 2Query CommandsSeveral special characters can be used to query the device about its settings.^ What is the default value for the setting(s).? Wha

12 - 3Examples of Query CommandsIn the following examples, a bracketed notation [ ] depicts a non-displayable response.Example #1:What is the range

12 - 4Trigger CommandsYou can activate and deactivate the imager with serial trigger commands. First, the imager must be put in Manual/Serial Trigger

12 - 5Program Keyboard Country*U.S.A.KBDCTY02-4BelgiumKBDCTY12-4BrazilKBDCTY162-4Canada (French)KBDCTY182-4Czech RepublicKBDCTY152-4DenmarkKBDCTY82-4F

12 - 6Keyboard Style *RegularKBDSTY02-6Caps LockKBDSTY12-6Shift LockKBDSTY22-7Automatic Caps LockKBDSTY62-7Emulate ExternalKeyboardKBDSTY52-7Keyboard

12 - 7Word Length: Data Bits, Stop Bits, and Parity7 Data, 1 Stop, Parity Even232WRD32-117 Data, 1 Stop, Parity None232WRD02-117 Data, 1 Stop, Parity

12 - 8Wand Emulation Transmission Rate10WNDSPD02-15*25WNDSPD12-1540WNDSPD22-1580WNDSPD32-15120WNDSPD42-15150WNDSPD52-15200WNDSPD62-15Wand Emulation Po

12 - 9Good Read Delay*No DelayDLYGRD03-3Short Delay (500 ms)DLYGRD5003-3Medium Delay (1000 ms)DLYGRD10003-3Long Delay (1500 ms)DLYGRD15003-3User-Speci

DisclaimerHoneywell International Inc. (“HII”) reserves the right to make changes in speci-fications and other information contained in this document

1 - 4Connecting the Imager with Keyboard WedgeNote: See "Imager Models" on page 1-2 to determine which interfaces apply to your imager.An im

12 - 10LED Power LevelOffPWRLDC03-11Low (50%)PWRLDC503-11*High (100%)PWRLDC1003-11Illumination Lights*Lights OnSCNLED13-11Lights OffSCNLED03-11Imager

12 - 11Preferred SymbologyOnPRFENA13-16*OffPRFENA03-16High Priority SymbologyPRFCOD##3-16Low Priority SymbologyPRFBLK##3-16Preferred Symbology Timeout

12 - 12Suffix Add SuffixSUFBK2##4-4Clear One SuffixSUFCL24-4Clear All SuffixesSUFCA24-4Function Code Tran smi t*EnableRMVFNC04-4DisableRMVFNC14-4Inter

12 - 13Secondary Code 39 Wand Emulation Wand Emulation Same Code Format2IFTYP646-2Wand Emulation Code 39 Format2IFTYP616-3Wand Emulation Multi BlockDe

12 - 14Hands Free Time-OutRange 0 - 300,000 msTRGPTO######6-7Scan Stand Scan Stand Mode2IFTRG46-8Scan Stand SymbolFNC36-8Presentation Presentation Mod

12 - 15Code 39 Check Char.*No Check Char.C39CK207-6Validate, But Don’t Tran smi tC39CK217-6Validate, and TransmitC39CK227-6Code 39 Message LengthMinim

12 - 16Straight 2 of 5 IndustrialDefault All Straight 2 of 5 Industrial SettingsR25DFT7-11Straight 2 of 5 Industrial*OffR25ENA07-11OnR25ENA17-11Straig

12 - 17ISBT Concatenation*OffISBENA07-15OnISBENA17-15Code 128 Message LengthMinimum (0 - 80) *0128MIN##7-16Maximum (0 - 80) *80128MAX##7-16Code 128

12 - 18UPC-A/EAN-13 with Extended Coupon Code*OffCPNENA07-20Allow ConcatenationCPNENA17-20Require ConcatenationCPNENA27-20UPC-E0 Default All UPC-ESett

12 - 19EAN/JAN-13 2 Digit Addenda2 Digit Addenda OnE13AD217-24*2 Digit Addenda OffE13AD207-245 Digit Addenda OnE13AD517-24*5 Digit Addenda OffE13AD507

1 - 5Connecting the Imager with USBNote: See "Imager Models" on page 1-2 to determine which interfaces apply to your imager.An imager can be

12 - 20MSI Check Character*Validate Type 10, but Don’t Tra nsm itMSICHK07-27Validate Type 10 and Tra nsm itMSICHK17-27MSI Message LengthMinimum (4 - 4

12 - 21PosiCode OffPOSENA07-31*OnPOSENA17-31A and B OnPOSLIM07-31A and B and Limited A OnPOSLIM17-31*A and B and Limited B OnPOSLIM27-31PosiCode Msg.

12 - 22MicroPDF417 Default All Micro PDF417 SettingsMPDDFT7-36MicroPDF417 OnMPDENA17-36*OffMPDENA07-36MicroPDF417 Msg. LengthMinimum (1-366) *1MPDMIN7

12 - 23Planet Code Check DigitTran smi tPLNCKX17-40*Don’t TransmitPLNCKX07-40British Post OnBPOENA17-41*OffBPOENA07-41Canadian Post OnCANENA17-40*OffC

12 - 24Data Matrix Default All Data Matrix SettingsIDMDFT7-46Data Matrix *OnIDMENA17-46OffIDMENA07-46Data Matrix Msg. LengthMinimum (1-3116) *1IDMMIN7

12 - 25Imaging Default CommandsDefault all Imaging Commands IMGDFT 8-1Image Snap Imaging Style - Decoding SNPSTY0 8-2*Imaging Style - Photo SNPSTY1 8-

12 - 26Image Ship (continued)Sharpen Edges (0-23) IMGEDG## 8-7*File Format - JPEG IMGFMT6 8-7File Format - KIM IMGFMT0 8-7File Format - TIFF binary IM

12 - 27Image Ship (continued)Image Crop - Top (0-480) *0 IMGWNT### 8-10Image Crop - Bottom (0-480) *479IMGWNB### 8-11Image Crop - Margin (0-238) *0IMG

12 - 28OCR Check CharacterOCR Mod. 10 Check Char. “OCRCHK0123456789”9-8OCR Mod. 36 Check Char. “OCRCHK0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ”9-8OCR User

13 - 113Product Specifications4600g and 4600rParameter Specification4600g/4600r Dimensions (Typical):Height6.2 inches (15.7 cm)Length5.3 inches (13.5

1 - 6Connecting the Imager with RS-232 Serial PortNote: See "Imager Models" on page 1-2 to determine which interfaces apply to your imager.1

13 - 24800iVibration Withstands 5G peak from 22 to 300 HzESD Tolerance 15 kV to any external surfaceParameter SpecificationDimensions (Typical):Height

13 - 3Standard Cable PinoutsKeyboard Wedge10 Pin RJ41 Modular Plugconnects to the imager handle1 2Cord shield3 Prog 14 Supply ground5 Terminal clock6

13 - 4Wand Emulation10 Pin Modular Plugconnects to the imager handle12Cord shield3 Tied to 5 Volt power 4 Supply ground56 Barcode data output7 5 Volt

13 - 5Serial Output 10 Pin RJ41 Modular Plugconnects to the imager handle12 Cord shield3 Tied to 5 Volt power4 Supply ground5 Receive data - Serial da

13 - 6USB10 Pin Modular Plugconnects to the imager handle12 Data +3 Tied to 5 volt power4 Supply ground567 5 volt power connection8910 Data -

14 - 114MaintenanceRepairsRepairs and/or upgrades are not to be performed on this product. These ser-vices are to be performed only by an authorized

14 - 2Replacing the Interface CableThe standard interface cable is attached to the imager with an 10-pin modular connector. When properly seated, the

14 - 3To Replace the 4600rp Interface Cable:1. Turn the power to the host system OFF.2. Disconnect the imager’s cable from the terminal or computer.3.

14 - 48. Screw the cord lock back in place over the cord.TroubleshootingThe imager automatically performs self-tests whenever you turn it on. If your

14 - 51. Scan the sample barcodes in the back of this manual. If the imager reads the sample barcodes, check that your barcode is readable.Verify tha

1 - 71. Turn off power to the computer.2. Disconnect the existing serial cable from the computer.3. Connect the appropriate interface cable to the ima

14 - 6

15 - 115Customer SupportTechnical AssistanceIf you need assistance installing or troubleshooting your device, please call your distributor or the near

15 - 2Product Service and RepairHoneywell International Inc. provides service for all its products through service centers throughout the world. To o

15 - 3Limited WarrantyHoneywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to

15 - 4by this warranty. This includes but is not limited to: cables, power supplies, cra-dles, and docking stations. HII extends these warranties only

A - 1AReference ChartsSymbology ChartSymbology AIM IDPossible AIM ID Modifiers (m)Code ID (hex)All Symbologies (0x99)Australian Post ]X0 A (0x41)Azte

A - 2Intelligent Mail Barcode ]X0 M (0x4D)Interleaved 2 of 5]Im0, 1, 3 e (0x65)Japanese Post ]X0 J (0x4A)KIX (Netherlands) Post ]X0 K (0x4B)Korea

A - 3Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier charact

A - 4ASCII Conversion Chart (Code Page 1252)Note:This table applies to U.S. style keyboards. Certain characters may differ depending on your Country

A - 5Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char128 80€€160 A0 192 C0 À 224 E0 à129 81 161 A1 ¡ 193 C1 Á 225 E1 á130 82 ‚ 162 A2 ¢ 194 C2 Â 22

1 - 8Programming the Interface - Plug and PlayPlug and Play barcodes provide instant imager set up for commonly used inter-faces.Note: After you scan

A - 6Code Page Mapping of Printed BarcodesCode pages define the mapping of character codes to characters. If the data received does not display with

Sample SymbolsUPC-A0 123456 7890Interleaved 2 of 5Code 128EAN-13Code 39Codabar1234567890Code 1289 780330 290951BC321A13579BCode 93123456-9$Straigh

Sample Symbols6543210ID-tag (UPU 4-State)J18CUSA8E6N062315014880TPDF417PostnetCode 49Car RegistrationZip Code1234567890Data MatrixQR CodeTest S ymbo l

Sample SymbolsAztecMaxiCodeMicro PDF417Package LabelTest MessageTest MessageOCR-B with Modulo 10 check characterOCR-A with Modulo 36 check character

OCR Programming Chartaedgchtlr

OCR Programming ChartTDAOSaveDiscard

Programming ChartACBFED1023

Programming ChartNote: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or dig

Honeywell700 Visions DriveP.O. Box 208Skaneateles Falls, NY 13153-020846gr-48i-UG Rev F2/09

1 - 9USB ConnectionIBM SurePosScan one of the following “Plug and Play” codes to program the imager for IBM SurePos (USB handheld imager) or IBM SureP

1 - 10USB PC or Macintosh® KeyboardScan one of the following codes to program the imager for USB PC Keyboard or USB Macintosh Keyboard. Scanning thes

1 - 11CTS/RTS EmulationACK/NAK ModeRS-232 Serial Port ConnectionAll communication parameters between the imager and terminal must match for correct da

1 - 12Serial Wedge Data Transmission PortUsing the following barcodes, set the port to which you want the scanned data to transmit. Port 1 correspond

1 - 13Each of the previous barcodes also programs the following suffixes for each symbology:.The IBM 4683 Port 9B HHBCR-2 Interface barcode also prog

and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a resident

1 - 1425 inches per second, Output Polarity to black high, and Idle State to high. (If you want to change the terminal ID only, without changing any

1 - 15Reading TechniquesThe imager has a view finder that projects a bright red or green aiming beam that corresponds to the imager’s horizontal field

1 - 16

2 - 12Terminal InterfacesTerminal IDIf your interface is not covered by a Plug and Play barcode from Chapter 1, then refer to Supported Terminals on p

2 - 2Supported Terminals Note: See "Imager Models" on page 1-2 to determine which interfaces apply to your imager.Terminal Model(s)Terminal

2 - 3* Default for 4600g/4600r/4600rp/4800iXX 05XX models. It is best to use the Plug andPlay barcodes, beginning on page 1-9, to program these inter

2 - 4Keyboard CountryScan the appropriate country code below to program the keyboard for your country. As a general rule, the following characters are

2 - 5Keyboard Country (continued)Latin AmericaNorwayPolandPortugalRomaniaRussiaSCSSlovakiaItalyNetherlands (Dutch)SpainSwedenSwitzerland (German)

2 - 6Keyboard Country (continued)Please refer to the Honeywell website (www.honeywell.com/aidc) for complete keyboard country support information and

2 - 7Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards).Automatic Caps Lock is used if you change the Caps

Honeywell International Inc. shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE

2 - 8support all keyboard country codes. New users should use the Windows mode. Refer to Keyboard Function Relationships, page 10-1 for CTRL+ ASCII

2 - 9Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default =

2 - 10RS-232 Baud RateBaud Rate sends the data from the imager to the terminal at the specified rate. The host terminal must be set for the same baud

2 - 11Parity provides a means of checking character bit patterns for validity.Default = None.RS-232 Receiver Time-OutThe unit stays awake to receive d

2 - 12receiver time-out by scanning the barcode below, then scanning digits from the inside back cover of this manual, then scanning Save. The range

2 - 13In Wand Emulation mode, the imager decodes the barcode then sends data in the same format as a wand imager. The Code 39 Format converts all sym

2 - 14Delay Between BlocksThis sets the delay time between data blocks. Default = 50ms.Overall ChecksumWhen this option is turned on, a computed chec

2 - 15Wand Emulation Transmission RateThe Transmission Rate is limited by the terminal’s ability to receive data without dropping characters. Default

2 - 16Wand Emulation IdleThe idle describes the state of the imager when no data is being transmitted. When in Wand Emulation mode, you must set the

3 - 13OutputGood Read IndicatorsBeeper – Good ReadThe beeper may be programmed On or Off in response to a good read. Turning this option off, only tu

South Korea (4600r only) MIC Class A EMC requirements.Mexico Conforms to NOM-019.InternationalEye Safety Statement: LEDThis device has been tested i

3 - 2Beeper Pitch – Good ReadThe beeper pitch codes modify the pitch (frequency) of the beep the imager emits on a good read. Default = Medium.Beeper

3 - 3LED flashes are in sync with one another. To change the number of beeps, scan the barcodebarcode below and then scan a digit (1-9) barcode and t

3 - 4Trigger ModesManual/Serial TriggerYou can activate the imager either by pressing the trigger, or using a serial trig-ger command (see Trigger Com

3 - 5Low Power Time-Out TimerScan the Low Power Time-Out barcode to change the time-out duration (in seconds). Then scan the time-out duration (from

3 - 6Scan Stand ModeWhen a unit is in Scan Stand mode, it remains idle as long as it sees the Scan Stand symbol (see below). When a different code is

3 - 7Presentation ModeThis programs the imager to work in Presentation mode. The LEDs are either off or at the lowest power for ambient conditions un

3 - 8Presentation SensitivityPresentation Sensitivity is a numeric range that increases or decreases the imager's reaction time to barcode presen

3 - 9Image Snap and ShipImage Snap and Ship tells the imager to take a picture (rather than read a bar-code) when the trigger is pressed. Once the pi

3 - 10Reread Delay only works when in Presentation Mode or Streaming Presentation™ Mode (page 3-8).User-Specified Reread DelayIf you want to set your

3 - 11If you have an aimer delay programmed (see Aimer Delay on page 3-12), the aimer will be at 100% power during the delay, regardless of the LED Po

3 - 12Imager Time-OutImager Time-Out powers down the imager after the unit has been idle for the specified time. To prevent the imager from powering

3 - 13Aimer ModeThis feature allows you to turn the aimer on and off. When the Interlaced bar-code is scanned, the aimer is interlaced with the illum

3 - 14imager’s field of view. The following diagram illustrates the default top, bottom, left, and right pixel positions, measured from the top and t

3 - 15Decode Search ModeThere are three selectable decode (scanning) modes:Full Omnidirectional - Searches for barcode features beginning at the cente

3 - 16Preferred Symbology classifies each symbology as high priority, low priority, or as an unspecified type. When a low priority symbology is prese

3 - 17Preferred Symbology Time-outOnce you have enabled Preferred Symbology and entered the high and low pri-ority symbologies, you must set the time-

3 - 18to apply the output sequence format. Locate the Hex value for that symbol-ogy and scan the 2 digit hex value from the Programming Chart (inside

3 - 19SEQBLK sequence editor start command62 code identifier for Code 399999 code length that must match for Code 39, 9999 = all lengths41 start chara

3 - 20Output Sequence Editor Require Output SequenceWhen an output sequence is Required, all output data must conform to an edited sequence or the i

3 - 21new symbols as long as the trigger is pulled. When this programming selection is turned Off, the Imager will only read the symbol closest to th

iChapter 1 - Getting StartedAbout This Manual ... 1-1Unpacking the Imager ...

3 - 22Video ReverseVideo Reverse is used to allow the imager to read barcodes that are inverted. The Off barcode below is an example of this type of

3 - 23* UprightRotate Code Clockwise 90°(Rotate Imager Counterclockwise)Upside DownRotate Code Counterclockwise 90°(Rotate Imager Clockwise)

3 - 24

4 - 14Data EditingPrefix/Suffix OverviewWhen a barcode is scanned, additional information is sent to the host computer along with the barcode data. T

4 - 2To Add a Prefix or Suffix:Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-4).Step 2. Determine the 2 digit Hex value from the Symbology

4 - 3To Clear One or All Prefixes or Suffixes:You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbol-ogy. When you Clea

4 - 4Prefix SelectionsSuffix SelectionsFunction Code TransmitWhen this selection is enabled and function codes are contained within the scanned data,

4 - 5Intercharacter, Interfunction, and Intermessage DelaysSome terminals drop information (characters) if data comes through too quickly. Interchara

4 - 6Next, scan the Character to Trigger Delay barcode, then the 2-digit hex value for the ASCII character that will trigger the delay ASCII Conversio

4 - 7Intermessage DelayAn intermessage delay of up to 495 milliseconds (in 5 ms steps) may be placed between each scan transmission. Scan the Interme

iiKeyboard Modifiers...2-7RS-232 Baud Rate...2-10RS-232

4 - 8

5 - 15Data FormattingData Format Editor IntroductionYou may use the Data Format Editor to change the imager’s output. For exam-ple, you can use the D

5 - 2Step 4. Code I.D.In the Symbology Chart (page A-1), find the symbology to which you want to apply the data format. Locate the Hex value for that

5 - 3F4 Send “xx” character “nn” times (Insert) leaving cursor in current cursor posi-tion. Syntax = F4xxnn (xx stands for the hex value for an ASCII

5 - 4ters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2.E5 Terminates character replacement. Syntax = E5.FE C

5 - 5Data Format EditorData FormatterWhen Data Formatter is turned off, the barcode data is output to the host as read (including prefixes and suffixe

5 - 6Alternate Data FormatsAlternate formats allow you “single shot” capability to scan one barcode using a different data format than your primary fo

6 - 16Secondary InterfaceBy switching secondary interface cables, the imager can, for example, commu-nicate with a portable data terminal (secondary i

6 - 2You can temporarily disable the secondary interface, but still retain the second-ary interface settings in the imager’s memory by scanning the Di

6 - 3The Code 39 Format barcode below sets the terminal ID to 61, and the Same Code Format barcode sets the terminal ID to 64.Wand Emulation Multi Blo

iiiReread Delay ... 3-9User-Specified Reread Delay... 3-10

6 - 4Overall ChecksumWhen this option is turned on, a computed check character is added at the end of the entire message. The check character is the

6 - 5Wand Emulation PolarityThe polarity can be sent as standard with black bars high, or reversed with white bars high. Default = Black High.Wand Em

6 - 6Secondary Trigger ModeManual/Serial TriggerYou can activate the imager either by pressing the trigger, or using a serial trig-ger command (see Tr

6 - 7Low Power Time-Out TimerScan the Low Power Time-Out barcode to change the time-out duration (in seconds). Then scan the time-out duration (from

6 - 8Scan Stand ModeWhen a unit is in Scan Stand mode, it remains idle as long as it sees the Scan Stand symbol. (See Scan Stand Symbol that follows.

7 - 17SymbologiesThis programming section contains the following menu selections. Refer to Chapter 12 for settings and defaults.• All Symbologies • I

7 - 2All SymbologiesIf you want to decode all the symbologies allowable for your imager, scan the All Symbologies On code. If on the other hand, you

7 - 3Codabar<Default All Codabar Settings>CodabarCodabar Start/Stop CharactersStart/Stop characters identify the leading and trailing ends of th

7 - 4When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar barcodes printed with a check character, but will no

7 - 5Codabar Message LengthScan the barcodes below to change the message length. Refer to Message Length Description (page 7-2) for additional inform