Honeywell 9782 Series Manual de usuario Pagina 10
- Pagina / 148
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9782 Series Conductivity/Resistivity Analyzer/Controller - Operator’s Manual 6/99x
APPENDIX B TWO-CELL APPLICATIONS................................................................B-1
Ion Exchange.................................................................................................................................................B-1
Reverse Osmosis............................................................................................................................................B-1
Conductivity/Resistivity/TDS Difference......................................................................................................B-2
Parts Rinsing..................................................................................................................................................B-2
Softener Monitoring.......................................................................................................................................B-3
Steam Power Measurements..........................................................................................................................B-3
Sodium Hydroxide & Hydrochloric Acid Concentration Measurements.......................................................B-4
APPENDIX C MICROPROCESSOR BOARD SWITCH SETTINGS ...........................C-1
Introduction ...................................................................................................................................................C-1
Location of switches ......................................................................................................................................C-1
SW1 - all positions set to off .........................................................................................................................C-1
SW2 - settings are dependent on options.......................................................................................................C-1
APPENDIX D USING A PRECISION CHECK RESISTOR..........................................D-1
Introduction ...................................................................................................................................................D-1
Set cal factor and calibration trim for ideal conditions..................................................................................D-1
Calculations for conductivity, resistivity, and TDS .......................................................................................D-1
Concentration values......................................................................................................................................D-2
- 9782 Series Two Cell 1
- Conductivity/Resistivity 1
- Analyzer/Controller 1
- Operator’s Manual 1
- Earth Connnection 2
- About This Document 3
- Contents 4
- 1. Introduction 15
- 1.2 Features 17
- +RQH\ZHOO 19
- 1.3.1 Keypad Use 20
- 1.3.2 Online Displays 22
- C1 0.58 µS 23
- C2 0.25 µS 23
- 01: 58:29 24
- 1.4 Menu Hierarchy 25
- [wide range models only] 26
- 1.5 Planning 27
- Selecting a strategy 30
- 2.1 Specifications 33
- 2.1.4 Electrical 34
- 2.1.5 Model Ranges 34
- 2.1.6 Operating Conditions 35
- 2.1.7 Outputs 36
- 2.1.9 AutoClean 37
- 2.1.10 Control 37
- (9782C-S0 only) 38
- 2.2 Model Number Breakdown 39
- 3.1 Overview 43
- 3.2 Unpacking and Preparing 44
- 3.3 Mounting 45
- Case Outline 46
- Panel Cutout 46
- 4. Power Wiring 51
- ) wire for ac power 53
- Section 2 53
- 4.4 Installing Power Wiring 54
- PE = Protective 55
- Earth Ground 55
- 5.1 Overview 57
- Ease of configuration 58
- Purpose of I/O setup 58
- Illustrations 59
- System defaults 59
- 5.3 Performing I/O Setup 60
- RELAY ACTIVATION 63
- STATE ON ALARM 63
- SELECT DE-ENERGIZE 63
- DISPLAY RESOLUTION 64
- RESOLUTION LOW 64
- UOM uS 64
- I/O SETUP COMPLETE 65
- PRESS 65
- ENTER TO CONTINUE 65
- 65
- CAT/RETRANSMISSION 66
- Cell Cell12− 68
- DISCRETE CONTROL 69
- CYCLE TMR 1 69
- 5.6 Configuring Alarms 72
- ADVANCED FEATURES 73
- 5.8 Configuring AutoClean 74
- COMPUTED VALUE 78
- SELECT DIFFERENCE 78
- 78
- 9782C-S0 79
- 9782C-W0 79
- 6. Input and Output Wiring 83
- Input and Output Wiring 85
- 6.4 Wiring Relays 89
- (simulated 92
- 7.1 Overview 95
- Rinse sequence 96
- Automatic Wash Setup 97
- AutoClean Operation 97
- 8. Calibration 99
- ATTENTION 101
- Calibration 103
- CAL TRIM 1 104
- REMOVE CAL TRIM C1 105
- Introduction 106
- TDS CVSN FACTOR C1 107
- TDS CVSN FACTOR C2 107
- 9. Diagnostics and Messages 109
- 9.2 System Status Messages 110
- 9.3 Process Alarm Messages 111
- Output affected by error 112
- 9.5 Off-Line Diagnostics 113
- KEYBOARD TEST 114
- 9.5.2 Output Tests 115
- OFFLINE FUNCTIONS 116
- OUTPUT/RELAY TEST 116
- 10. Maintenance 117
- 10.2 Output Calibration 119
- MAINTENANCE 120
- INSTRUMENT SETUP 120
- LEAD RESISTANCE COMP 120
- DIAGNOSTICS 120
- 120
- OUTPUT CALIBRATION 121
- MENU TO EXIT 121
- 121
- UPDATE TAG DATA 122
- HONEYWELL INC 122
- 122
- Stored in Memory 123
- FACTORY PASSWORD 124
- 124
- ENTER PASSWORD 124
- SCREEN CONTRAST 125
- Settings 127
- MAINTENANCE 129
- 10.9 Replacing the Fuse 130
- Maintenance 131
- 11.1 Overview 133
- 11.2 Part Numbers 134
- Appendix A 137
- Proportional Control Tuning 137
- Appendix B 139
- Two-Cell Applications 139
- Parts Rinsing 140
- Softener Monitoring 141
- Steam Power Measurements 141
- Appendix C 143
- Appendix D 145
- Honeywell, Inc 148
- 1100 Virginia Drive 148
Relacionado con productos y manuales para Hardware Honeywell 9782 Series
(243 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales